ข้ามไปที่เนื้อหาหลัก

GRBL Error List




Code

Message

Description

1Expected command letterG-code words consist of a letter and a value. Letter was not found.
2Bad number formatMissing the expected G-code word value or numeric value format is not valid.
3Invalid statementGrbl '$' system command was not recognized or supported.
4Value < 0Negative value received for an expected positive value.
5Setting disabledHoming cycle failure. Homing is not enabled via settings.
6Value < 3 usecMinimum step pulse time must be greater than 3usec.
7EEPROM read fail. Using defaultsAn EEPROM read failed. Auto-restoring affected EEPROM to default values.
8Not idleGrbl '$' command cannot be used unless Grbl is IDLE. Ensures smooth operation during a job.
9G-code lockG-code commands are locked out during alarm or jog state.
10Homing not enabledSoft limits cannot be enabled without homing also enabled.
11Line overflowMax characters per line exceeded. Received command line was not executed.
12Step rate > 30kHzGrbl '$' setting value cause the step rate to exceed the maximum supported.
13Check DoorSafety door detected as opened and door state initiated.
14Line length exceededBuild info or startup line exceeded EEPROM line length limit. Line not stored.
15Travel exceededJog target exceeds machine travel. Jog command has been ignored.
16Invalid jog commandJog command has no '=' or contains prohibited g-code.
17Setting disabledLaser mode requires PWM output.
20Unsupported commandUnsupported or invalid g-code command found in block.
21Modal group violationMore than one g-code command from same modal group found in block.
22Undefined feed rateFeed rate has not yet been set or is undefined.
23Invalid gcode ID:23G-code command in block requires an integer value.
24Invalid gcode ID:24More than one g-code command that requires axis words found in block.
25Invalid gcode ID:25Repeated g-code word found in block.
26Invalid gcode ID:26No axis words found in block for g-code command or current modal state which requires them.
27Invalid gcode ID:27Line number value is invalid.
28Invalid gcode ID:28G-code command is missing a required value word.
29Invalid gcode ID:29G59.x work coordinate systems are not supported.
30Invalid gcode ID:30G53 only allowed with G0 and G1 motion modes.
31Invalid gcode ID:31Axis words found in block when no command or current modal state uses them.
32Invalid gcode ID:32G2 and G3 arcs require at least one in-plane axis word.
33Invalid gcode ID:33Motion command target is invalid.
34Invalid gcode ID:34Arc radius value is invalid.
35Invalid gcode ID:35G2 and G3 arcs require at least one in-plane offset word.
36Invalid gcode ID:36Unused value words found in block.
37Invalid gcode ID:37G43.1 dynamic tool length offset is not assigned to configured tool length axis.
38Invalid gcode ID:38Tool number greater than max supported value.

ความคิดเห็น

โพสต์ยอดนิยมจากบล็อกนี้

การติดตั้งโปรแกรม GRBL CONTROL สำหรับ MINICNC แบบ USB

สิ่งที่ต้องเตรียมการ 1.  ชุด CNC Controller GRBL Control   ซึ่งทำการ Download ได้จาก Link นี้ 2.   ชุด CNC Controller ที่มี GRBL Firmware  Software GRBL Control  หากท่านที่ต้องการทราบ ขั้นตอนการติดตั้ง GRBL Firmware สามารถศึกษาได้จาก Link นี้ครับ 3.  Drivers USB To Serial  ที่มาพร้อมกับ CNC Controller  ชุดควบคุม Minicnc แบบ Grbl ที่ต้องใช้การควบคุมผ่าน Serial Port ซึ่งหลายคนอาจเข้าใจว่าเป็นการควบคุมผ่าน USB เป็นความเข้าใจที่คลาดเคลื่อน เนื่องจาก โปรแกรมควบคุม CNC GRBL จะใช้การควบคุมผ่าน Serial Port ของ Micro controller (Arduino)  แต่ในการสื่อสารปัจจุบัน ช่อง Serial Port ของ PC Commuter แทบจะหาไม่ได้เลย จึงจะต้องใช้ อุปกรณ์ Interface ดัดแปลงผ่านช่อง USB ของ PC Computer จึงต้องมี Software Driver ควบคุม ผู้ผลิต Chip USB Converter มีหลายราย ดังนั้นในการใช้ USB To Serial Port ต้องทราบข้อมูลของ Software USB Drivers และ เลือกใช้ให้ตรงกัน จึงจะทำให้ช่องสื่อสารนี้ใช้งานได้ และ ผู้ผลิต Arduino ได้นำ Chip ที่มี USB To Serial port มาประกอบใว้เพื่อให้ความสะดวกกับผู้ใช้ แต่เนื่องจากผู

Info graphic สำหรับ GRBL